“Your walls support your home. The weather out there will not be nice for the exterior walls of your house. It’s not enough to paint the wall. After dealing with rain, snow, wind, dust, and the heat of the outside environment, the paint will start peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
“The outer part of your home’s wall is usually covered with a lot of dust and dirt that sticks to it. To ensure the efficiency of the whole process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned using a broom, brush, or scraper. Then use a power washer to finish it off.”
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time on the exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is done. You can fill them with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The mixture of cement penetrated inside the cracks and sealed them. You should remove all the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal for the walls. Allow it to become dry after that.
Step 5: Pick the right water-proofer
There are many waterproof products available in the market. You need to pick the right one for the wall. Pick the water-proofer if it is a concrete wall or a silicate one.
It is possible to choose between a silicate-based concrete sealer and a concrete waterproofing coating. Pick a plaster waterproof Additive that will add strength to your walls.
Step 6: Apply the water-proofer
Apply the water-proofer with a roller or brush. If you want to apply more than one layer, you should give a thin coat first. Let the first coat dry before adding the second one.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement waterproofer. You can apply it on the wall.
After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your walls.
Step 8: Consider adding gravel
If you want to lay the drainage pipes below the footer, you need a proper base. The drainage pipes are going to get adequate support from a gravel base. Gravel provides enhanced protection.
You need to lay the drainage pipe-cover along with the gravel. Next to the footer, level the position of the gravel and back-fill it. The pipe needs to be covered for at least 3-inches.
Step 9: Add a fabric barrier
Attach the fabric barrier to the pipe. Ensuring that a fabric barrier is in place will prevent the formation of dirt. Then back-fill the trench and build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,
Conclusion:
“Your home gets a new life and strength when it’s waterproof. Magicrete can help you find good solutions for your walls. At a very low and affordable price, Magicrete has quality service and proper weatherproofing.”
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”
Discussion about this post